|
|
| Heat Exchanger > HTST Heat Exchanger |
HTST Heat Exchanger |
 |
Feldmeier HTST Skid |
| Mfg: Feldmeier |
Model: |
| Stock No. MTGP001.150 |
Serial: |
| Feldmeier HTST Skid. Stainless steel construction. 3-Sections with: pasteurizer, regeneration, chiller. Pasteurizer consists of 16 tubes with inner tube dimensions of 1-1/2 in. dia. x 9 ft. 2 in. L and outer tube dimensions of 2-1/2 in. dia. x 8 ft. 11 in. L. Regeneration consists of 60 tubes with inner tube dimensions of 1-1/2 in. dia. x 9 ft. 2 in. L and outer tube dimensions of 2 in. dia. x 8 ft. 11 in. L. Chiller consists of 24 tubes with inner tube dimensions of 1-1/2 in. dia. x 9 ft. 2 in. L and outer tube dimensions of 2-1/2 in. dia. x 8 ft. 11 in. L. APV pump, Type W+70/40, S/N: 100048812. WEG Motor, 20 hp, 3520 rpm, 208-230/460 V, 46.5/23.3 amps, 60 Hz, 3 phase. Overall dimensions 133 in. L x 97 in. W x 103 in. H.
|
|
|
|
APV Anhydro Triple Tube Pasteurizer |
| Mfg: APV Crepaco |
Model:CTT-C-50.B-38-25-3M |
| Stock No. BIIR601. |
Serial: |
| APV Anhydro Triple Tube Pasteurizer. Model: CTT-C-50.B-38-25-3M. Last used to pasteurize .25 to 4 gpm of 15 degree juice from 30 °F/50 °F to 200 °F; then to cool the same quantity of product from 200 °F to 50 °F/40 °F. Also used to pasteurize .25 to 4 gpm of 50 degree brix juice concentrate from 30 °F/50 °F to 200 °F; then to cool the same quantity of product from 200 °F to 50 °F/40 °F. 316 stainless steel (product side); 304 stainless steel (service side). Overall dimensions: 12 ft. L x 6 ft. W x 7 ft. H. Used in APV pilot plant as grape juice heater/cooler.
|
|
|
|
Cherry Burrell Stainless Steel Skid-Mounted Vegetable Juice Pasteurizer-10,660 lbs/hr |
| Mfg: Cherry Burrell |
Model: |
| Stock No. G226-B.150 |
Serial: |
| Cherry Burrell Stainless Steel Skid-Mounted Vegetable Juice Pasteurizer-10,660 lbs/hr. Skid includes: Cherry Burrell plate heat exchanger, Model 217SB-2. S/N 2325, Siemens PLC with keypad, Epson dot matrix printer, balance tank, holder tube, divert valve, centrifugal timing pump with mag meter based timing system, deaerator, product removal pump, vacuum pump, shell and tube hot water make-up set, and interconnecting piping. Duty to pasteurize 10,600 lbs/hr of single strength vegetable juice with a temperature progression of 40-90-230-260-129-99-70-65 using 22,500 lbs/hr of 260 °F water, 22,500 lbs/hr of 265 °F hot water and 22,500 lbs/hr of 55 °F potable water.
|
|
|
|
APV Pasteurizing Skid with CIP Capability |
| Mfg: APV |
Model:SR15 |
| Stock No. FCCP001.130 |
Serial: |
| APV Pasteurizing Skid with CIP Capability. Capacity: 10 gpm. APV Control Panel. Project No. 112-00756. Power supply: 230 V, 20 amps, 60 Hz, 3 phase. Anderson Chart Recorder ACR 700 Series. Model: 71010000002100W. S/N: 0220455. Power supply: 115 VAC, 50-60 Hz. Acme Transformer. Type: TA-2-81219. Power supply: 2000 VA, 50-60 Hz. Allen Bradley Circuit Breaker. Part No. 1492-GH100.
|
|
|
|
APV SR6 HTST |
| Mfg: APV |
Model:SR6GLM |
| Stock No. NEAF003. |
Serial: 25059 |
| APV SR6 HTST. Model: SR6GLM. S/N: 25059. Number of plates: 51. Heat transfer surface area: approx. 325.125 sq. ft. Hot water centrifugal pump with motor. Danfoss Magflo Flowmeter System, Model: MAG1100 Food, S/N: 141702T280, size DN: 50, fluid temperature: -20 to 150 °C, lining: ceramic, power supply: 115/230 Vac, 50-60 Hz. Fisher Valve Actuator, Type: 667, S/N: CN 841808, size: 34, travel: 3/4 in., operating range: 3-15 psi, rating: 250/100 °F, plug: 316SS, stem: 316SS, seat: 316SS, body: bronze. 1990 Wessels Co. Pressure Tank- 10 Gallon, MAWP: 150 psi @ 450 °F, MDMT: -20 °F @ 150 psi. Inlets: (1) 1-1/2 in. dia. NPT, (2) 2-1/2 in. dia. S-line, (1) 4 in. dia. S-line. Outlets: (1) 1-1/4 in. dia. bevel with hex, (3) 2-1/2 in. dia. S-line, (1) 3 in. dia. S-line, (1) 4 in. dia. S-line. Overall dimensions: 98 in. L x 72 in. W x 95 in. H.
|
|
|
|
Stork 4-Stage Pasteurizer System |
| Mfg: Stork |
Model: |
| Stock No. 850.TGP360a.27a |
Serial: |
| Stork 4-Stage Pasteurizer System. Pre-heater, pre-cooler, pasteurizer and chiller located inside 316 stainless steel tank. This was originally owned by Tropicana Products Inc. and was last used to process juice. Misc. 316 stainless steel storage tanks, high shear mixer with heat. Dimensions: 87 in. W x 80 in. H. 52 gpm with Ambient heated to 153 °F and chilled to 33 °F with 86 percent regeneration. Easy to clean, in great operational shape. Can handle no pulp and high pulp products. Tropicana Products Inc. Open system type 12.000 SC, order number S70490/653004, Tubular Heat-exchanger 19280.
|
|
|
|
APV Crepaco HTST |
| Mfg: APV Crepaco |
Model:SR35 |
| Stock No. CFPH359.41a |
Serial: 76827 |
| APV Crepaco HTST. Model: SR35. S/N: 76827. Nat'l Bd: 3067. W.O: 21308-1. Number of plates: 148. Heat transfer surface area: approx. 632 sq. ft. Number of dividers: 1. MAWP: 150 psig @ 275°F. MDMT: 5°F @ 150 psig. Bell & Gossett Shell & Tube Heat Exchanger, S/N: 89R7762-01-4, Nat'l Bd: 9213, shell side MAWP: 150 psi @ 375°F, shell side MDMT: -20°F @ 150 psi, tube side MAWP: 125 psi @ 375°F, tube side MDMT: -20°F @ 125 psi. Centrifugal Pump, S/N: 1527422 D.8. U.S. Electric Motor, 3 hp, 1750 rpm, 230/460 V, 9.0-4.5/10.5-5.25 amps, 60 Hz, 3 phase. Condensate Tank- 13 Gallon, inside straight-wall dimensions: 1 ft. dia. x 2 ft. 4 in. L. Fisher Pneumatic Valve Positioner, S/N: 11184269, Actuator type: 667, max. supply: 90 psi, operating range: 3-15 psi, Body type: ED, material: iron, size: 3, seat: 416 sst, stem plug: 316 sst/ 416 sst, rating: CL125. (3) Stainless Steel Pneumatic Valves. Hartel Stainless Steel Control Panel, dimensions: 2 ft 6 in. L x 1 ft. W x 3 ft. H. Inlets: (2) 2 in. dia. ports, (1) 3 in. dia. port, (1) 2 in. dia. I-line fitting, (1) 2 in. dia. flanged port. Outlets: (2) 4 in. dia. flanged ports, (1) 1-1/2 in. dia. port, (2) 3 in. dia. ports, (1) 2 in. dia. flanged port. Overall dimensions: 8 ft. 7 in. L x 5 ft. 8 in. W x 11 ft. 2-1/2 in. H.
|
|
|
|
APV Pasturizing System |
| Mfg: APV |
Model:CTTC104-88.9-60 |
| Stock No. SGM4136.110 |
Serial: 589CPSI |
| APV Pasturizing System. Model: CTTC104-88.9-60. 3. S/N: 589CPSI.
|
|
|
|
APV HTST Skid with Titanium Plates |
| Mfg: APV |
Model:SR-35 |
| Stock No. BIIR05. |
Serial: 16032 |
| APV HTST Skid with Titanium Plates. Model: SR-35. S/N: 16032. APV Heat Exchanger: (55) Titanium plates. (2) divider plates. Heat transfer surface area: 235.27 (approx.). Holding tube diameter: 2 in. Capacity: 2-1/2 gal. Heat transfer surface area: 8 sq. ft. (approx.). Carver Centrifugal Pump, Type: 2.5x2x7LA-33D, S/N: 82861, 3450 rpm (final), impeller diameter: 5-1/2 in. Baldor Industrial Motor, 5 hp, 3450 rpm, 208-230/460 V, 13.2-12/6 amps, 60 Hz, 3 phase. Inlets: (1) 3 in. dia. S-line fitting, (1) 3 in. dia. with a 7 in. dia. flange and (4) 3/4 in. dia. attachment holes at a center-to-center distance of 6 in. Outlets: (1) 3 in. dia. S-line fitting, (2) 3 in. dia. with a 7 in. dia. flange and (4) 3/4 in. dia. attachment holes at a center-to-center distance of 6 in. Overall dimensions: 9 ft. 10 in. L x 68 in. W x 95 in. H.
|
|
|
|
APV Crepaco HTST |
| Mfg: APV Crepaco |
Model:SR35 |
| Stock No. CFPH358.41a |
Serial: 76828 |
| APV Crepaco HTST. Model: SR35. S/N: 76828. Nat'l Bd: 3066. W.O: 21308-2. Number of plates: 149. Heat transfer surface area: approx. 637 sq. ft. Number of dividers: 1. MAWP: 150 psig @ 275°F. MDMT: 5°F @ 150 psig. Bell & Gossett Shell & Tube Heat Exchanger, S/N: 89R77624-01-1, Nat'l Bd: 9210, shell side MAWP: 150 psi @ 375°F, shell side MDMT: -20°F @ 150 psi, tube side MAWP: 125 psi @ 375°F, tube side MDMT: -20°F @ 125 psi. Bell & Gossett Centrifugal Pump, Model: 1531-2.5AB-6.375BF. ID No. RLD20475B40. Baldor Industrial Motor, 3 hp, 1725 rpm, 208-230/460 V, 8.5-8.2/4.1 amps, 60 Hz, 3 phase. Condensate Tank- 13 Gallon, Inside straight-wall dimensions: 1 ft. dia. x 2 ft. 4 in. L. Fisher Pneumatic Valve Positioner, S/N: 11184270, Actuator type: 667, max. supply: 90 psi, operating range: 3-15 psi, Body type: ED, material: iron, size: 3, seat: 416 sst, stem plug: 316 sst/ 416 sst, rating: CL125. (3) Stainless Steel Pneumatic Valves. Hartel Stainless Steel Control Panel, dimensions: 2 ft 6 in. L x 1 ft. W x 3 ft. H. Inlets: (2) 3-1/2 in. dia. ports (product), (4) 3-1/2 in. dia. port. (steam). Outlets: (2) 3-1/2 in. dia. ports. (product), (1) 1-1/2 in. dia. port (steam), (1) 2-1/2 in. port. (steam), (2) 3-1/2 in. dia. (steam). Bell & Gossett overall dimensions: 7 ft. 1 in. L x 3 ft. 10 in. W x 6 ft. 3 in. H. APV Crepaco Heat Exchanger overall dimensions: 8 ft. L x 5 ft. 8 in. W x 6 ft 4 in. H.
|
|
|
|
Skid Mounted Tubular Pasteurizer |
| Mfg: |
Model: |
| Stock No. GMFP003. |
Serial: P-003-93 |
| Skid Mounted Tubular Pasteurizer. S/N: P-003-93. Heat exchanger dimensions: 10 in. diameter x 61 in. L. (2) Condensate Tanks- 10 Gallon, MAWP: 125 psi at 210 °F. Unit is equipped with (2) electro-pneumatic valves and (2) Jordan pressure relief valves. Stainless Steel Balance Tank 30 Gallon. 2 in. inlet, (1) 3 in. Outlet, (2) 2 in. outlet. Inside dimensions 20 in. diameter, 24 in. depth. Overall dimensions: 43 in. L x 21 in. W x 37 in. H. Bell & Gossett Centrifugal Pump, Model: 11/28C, MAWP: 175 psi, capacity: 60 gpm at 50 ft, 1800 rpm maximum. Waukesha 30 positive displacement pump. (2) Dickson Temperature Chart Recorders. Model: KT602. S/N: 00252182, 01008504, Recorders feature touchpad controls and digital display. Single pen recorders with attached thermocouples. NIST: 5.1 °C, -7.3 °C, -8.3 °C. Input: 120 VAC, 16 watts, 60 Hz. Output: 9 VDC, 1 amp. FAD
|
|
|
|
APV Junior HTST Skid |
| Mfg: APV |
Model: |
| Stock No. RLOL488.5a |
Serial: |
| APV Junior HTST Skid. Capacity: up to 2 gpm. APV Plate Heat Exchanger. Holding tube - 3/4 Gallon. Fristam FPX Series Centrifugal Pump, Model: FPX712, S/N: 12168434. Motor, 3 hp, 3475 rpm, 230/460 V, 8.6/4.3 amps, 60 Hz. Stainless Steel Balance Tank- 11 Gallon. Inlets: (2) 1-1/2 in. dia. S-line fittings (holding tube), (4) 1 in. dia. S-line fittings (heat exchanger). Outlets: (4) 1 in. dia. S-line fittings (holding tube), (4) 1 in. dia. S-line fittings (heat exchanger). Overall dimensions: 77 in. L x 48 in. W x 75 in. H.
|
|
|
|
Bell & Gossett Shell and Tube Heat Exchanger |
| Mfg: Bell & Gossett |
Model:SU107-2 |
| Stock No. BFLV003. |
Serial: |
| Bell & Gossett Shell and Tube Heat Exchanger. Model: SU107-2. Heating surface area: 101 sq. ft. 2-Pass. (76) 3/4 in. dia. x 83 in. L copper tubes. Design pressure tube side: 125 psi. Test pressure tube side: 250 psi. Design pressure shell side: 150 psi. Test pressure shell side: 300 psi. Design temperature tube & shell side: 375 °F. The “SU” Heat Exchanger is an instantaneous type, designed to heat liquids with steam. No space-wasting, expensive storage tank is needed. Inlets: (1) 3 in. dia. 4-bolt steam flange, (1) 2-1/2 in. dia. S-Line fitting. Outlets: (1) 2 in. dia. bevel fitting, (1) 2-1/2 in. dia. S-Line fitting, (1) 1/2 in. globe valve. Overall dimensions: 102 in. L x 28-1/2 in. W x 50 in. H.
|
|
|
|
Ammonia Plate Chiller |
| Mfg: |
Model: |
| Stock No. HDAF525.56a |
Serial: |
| Ammonia Plate Chiller. Unit houses (7) 45 in. W x 61-1/2 in. H Plates with (7) 1 in. dia. inlets, (7) 1 in. dia. outlets. Tank capacity: 300 gal. Inlets: (1) 6 in. dia. port. Outlets: (1) 3 in. dia. port, (1) 2 in. dia. NPT (female) valve discharge, (1) 4 in. dia. S-Line overflow, (1) 1-1/2 in. dia. S-Line overflow, (1) 1 in. dia. S-Line overflow, (1) 1-1/2 in. dia. bevel, (1) 2 in. dia. S-Line discharge. (1) 2-1/2 in. dia. S-Line discharge. Overall dimensions: 106 in. L x 48 in. W x 96 in. H.
|
|
|
|
APV HTST Press- 5,000 GPH |
| Mfg: APV |
Model:R51 |
| Stock No. pHDMD300.73a |
Serial: 17064 |
| APV HTST Press- 5,000 GPH. APV Crepaco Plate Heat Exchanger, Model R51, S/N 17064. (238) Diagonal flow plates. Surface heating area: 1198 sq. ft. (2) Dividers. (2) Pumps - (1) Fristam, (1) APV. Holding tube: 23 gallons. Balance tank: 152 gallon.
|
|
|
|
Chester Jensen Film Plate Chiller |
| Mfg: Chester Jensen |
Model:4-2-24-24 |
| Stock No. HDAF526.51 |
Serial: 4-248-125. |
| Chester Jensen Film Plate Chiller. Size: 4-2-24-24, S/N: 4-248-125. (8) 60 in. L x 30 in. W plate with 24 Coils. Reservoir – 25 Gallons. Inlets: (1) 1-1/2 in. dia. port, (1) 2 in. dia. port. Outlets: (1) 1-1/2 in. dia. port, (1) 2 in. dia. port. (1) 2 in. dia. S-Line. Overall dimensions: 87 in. L x 23 in. W x 89 in. H.
|
|
|
|
Mojonnier Preheat Raw Milk Pasteurizing Skid |
| Mfg: Mojonnier |
Model: |
| Stock No. RCCB287.42a |
Serial: 5024 |
| Mojonnier Preheat Raw Milk Pasteurizing Skid. Float/flow Limit Unit. SN: 5024. 36 in. dia. x 20 in. H, Flow Limit Device Spec: Flow rate at which cut out occurs @ 48gpm / 24801 lbs./hr Holding Tube Spec, (12) coils at 2 in. dia. 96 ft. 6 in. L, Net content: 13.8 Gallons. Time holding period @ 38.6 gpm flows equals two 21.4 seconds. , float/flow limit unit, S/N 5024 @ (5) Pumps: Tri-Clover, Lincoln Motor, 7.5 hp, 3490 rpm, 230/460 V, 18.6/9.3 amps, 60 Hz, 3 phase. Inlet: (1) 3 in. dia. S-Line. Outlet: (1) 1-1/2 in. dia. S-Line. Tri-Clover, Model: C216ME5ST-S, S/N: H3175, 3/4 hp, 1725 rpm, 208-230/460 V, 2.4-2.4/1.2 amps, 60 Hz, 3 phase. Inlet: (1) 2-1/2 in. dia. S-Line. Outlet: (1) 1-1/2 in. dia. S-Line. Tri-Clover, Model: C216ME1ST-S, S/N: H3291, 5 hp, 3450 rpm, 230/460 V, 17.4/8.7 amps, 60 Hz, 3 phase. Inlet: (1) 2-1/2 in. dia. S-Line. Outlet: (1) 1-1/2 in. dia. S-Line. Tri-clover with Motor, Model: C218ME14T-S, S/N: H3178, Inlet: (1) 3 in. dia. S-Line. Outlet: (1) 1-1/2 in. dia. S-Line. Balance tank - 74 Gallons with associated steam valves (approx. 10), (1) 2 stem flow diversion valve and stainless steel pipe within, (3) Air Pilot Float Switch Probes, Model: PMH, 5 in. dia. x 18 in. H. Strainer, 1-1/2 in. dia. spray bridge. Inlets: (6) 1-1/2 in. dia. S-Line, (1) 2 in. dia. S-Line. Outlets: (1) 4 in. dia. Overflow. Overall dimensions: 84-1/2 in. L x 69 in. W x 95 in. H.
|
|
|
|
APV Crepaco HTST Plate Heat Exchanger |
| Mfg: APV Crepaco |
Model:CR5 |
| Stock No. RCCB181B.158 |
Serial: D-1498 |
| APV Crepaco HTST Plate Heat Exchanger. Model: CR5. S/N: D-1498. Inlets: (1) 4 in. dia. ACME fitting. Outlets: (1) 4 in. dia. ACME fitting. Overall dimensions: 13 ft. L x 40 in. W x 103 in. H. Floater, inlets/outlets: (4) 4 in. dia. ACME fittings. Overall dimensions: 17 in. L x 12 in. W x 67 in. H. (2) Dividers, inlets/outlets: (4) 4 in. dia. ACME fittings. Overall dimensions: 20-1/2 in. L x 4 in. W x 67 in. H. Stainless Steel Balance Tank- 100 Gallon. Inlets: (1) 1-1/2 in. dia. ACME fitting, (1) 2 in. dia. S-line fitting, (2) 2-1/2 in. dia. S-line fitting, (1) 4 in. dia. S-line fitting. Outlets: (1) 2-1/2 in. dia. NPT (drain), (1) 3 in. dia. ACME fitting (side), (1) 3 in. dia. S-line discharge, (1) 6 in. dia. overflow. Stainless Steel 8-Pass Holding Tube- 30 Gallon, heat transfer surface area: approx. 70 sq. ft. Overall dimensions: 13 in. L x 26 in. W x 67 in. H.
|
|
|
|
APV Model R56S HTST System |
| Mfg: |
Model: |
| Stock No. 280.RBD148a.0 |
Serial: |
| APV Model R56S HTST System size 3 frame, serial number 16926 upgraded by AGC to Pro-5 model, 3-sections, 2-1/2in holding tube 6ft x 10-pass, (5) air actuated valves, 30 gal. stainless steel balance tank, control panel with Anderson circular chart recorder/temp. control, (2) Anderson 801 loop controller, digital readout, Taylor chart recorder & Ampco clean up pump. Last used in Two effect Condensed Skim Milk Evaporator
Duty 1 - Skim Milk 22,000 pph 40-64-190 using 100 gpm 193 degree hot water
Duty 2 - Condensed Skim Milk 5,000 pph 151-44-37 using 80 gpm 34 degree ice water
|
|
|
|
Heinzen HMI Pasteurizing Conveyor |
| Mfg: Heinzen |
Model:SGL.LANE W/INFEED GATE |
| Stock No. SFEP011.8a |
Serial: 13810 |
| Heinzen HMI Pasteurizing Conveyor. Model: SGL.LANE W/INFEED GATE. S/N: 13810. Maximum aperture/clearance above belt: 24 in. W x 5 in. H. Height at conveyor infeed/exit: 92/74 in. (3) Baldor Industrial Washdown Duty Motors, 1/2 hp, 1750 rpm, 230/460 V, 1.6/.8 amps, 60 Hz, 3 phase. (2) Boston Gear Drives, 60 ratio, 29.61 rpm (final, infeed and pasteurizing conveyors). Boston Gear Drive, 30 ratio, 58.3 rpm (final, exit conveyor). Inlets: (1) 1 in. dia. PVC (dual spray bridge), (1) 2 in. dia. S-line fitting. Outlets: (1) 3/4 in. dia. PVC (final spray), (1) 4 in. dia. S-line fitting, (2) 6 in. dia. vents each with 11 in. dia. flanges and (8) 3/4 in. dia. thru-holes at a center-to-center distance of 3-1/2 in. Overall dimensions: 20 ft. 3 in. L x 58 in. W x 108 in. H.
|
|
|
|
APV Plate Heat Exchanger |
| Mfg: APV |
Model:R51 |
| Stock No. 120.ME88.20 |
Serial: 24447 |
| APV Plate Heat Exchanger. Model: R51. S/N and W.O: 24447. Number of dividers: 2. Inlets/outlets: (11) 3 in. dia. S-line fittings. Overall dimensions: 8 ft. 9 in. L x 2 ft. 10 in. W x 7 ft. 10 in. H.
Parker Hydraulic Torque Link, S/N: 51758, inlets/outlets: (4) 1/2 in. dia. NPT fittings. Overall dimensions: 2 ft. 5 in. L x 1 ft. 9 in. W x 6 ft. 9 in. H. RTD
|
|
|
|
1992 Mueller ACCU-THERM Plate Heat Exchanger HTST Stainless Steel |
| Mfg: Mueller |
Model:AT161 FFB-10 |
| Stock No. 650.JMB245a.30 |
Serial: 101176-4 |
| 1992 Mueller Accu-Therm Plate Heat Exchanger HTST. Stainless Steel. Model AT161FFB-10, Part Number 9814223, S/N 101176-4. , Complete with (118) Plates with Fittings (***Glycol Chilled***)
|
|
|
|
Stainless Steel HTST Control Panel |
| Mfg: |
Model: |
| Stock No. HDYA049.20 |
Serial: |
| Stainless Steel HTST Control Panel. Maselli Misure S.p.A. Brix Rafractrometric Receiver, Model: RIT2-600. Allen-Bradley PLC5/80 Controller. Air Valve Solenoids. Power Supply. Cathode Ray Tube and Cathode Ray Tube Control Circuit Board. UPS (Uninterruptible Power Supply). Codex Modem. Allen-Bradley Data Highway Communication Interface. (1) 1 ft. 4 in. W x 1 ft. H screen with keyboard. Overall dimensions: 6 ft. 4 in. L x 3 ft. 4 in. W x 7 ft. 1/2 in. H.
|
|
|
|
Circular Holding Tube on Stand- 20 Gallon |
| Mfg: |
Model: |
| Stock No. SFF579.2 |
Serial: |
| Circular Holding Tube on Stand- 20 Gallon. Tube dimensions: 4 in. x 419 in. L. Inlets: (1) 2-1/2 in. dia. bevel with hex nut fitting. Outlets: (1) 2-1/2 in. ACME fitting. Overall dimensions: 55 in. diameter x 75 in. H.
|
|
|
|
APC Dual Stem Flow Diversion Valve |
| Mfg: APC |
Model: |
| Stock No. SFF580b.4 |
Serial: |
| APC Dual Stem Flow Diversion Valve.
|
|
|
|
Stainless Steel Holding Tube- 20 Gallon |
| Mfg: |
Model: |
| Stock No. CCFP537. |
Serial: |
| Stainless Steel Holding Tube- 20 Gallon. Holding tube consists of (8) stainless steel tubes, temperature probe, and temperature gauge. Heating transfer surface area: Approx. 50 sq. ft. Overall dimensions: 9 ft. 3 in. L x 26 in. W x 68 in. H.
|
|
|
|
Feldmeier Stainless Steel Holding Tube- 30 Gallon |
| Mfg: Feldmeier |
Model: |
| Stock No. OI177. |
Serial: |
| Feldmeier Stainless Steel Holding Tube- 30 Gallon. Tube dimensions: (4) 3 in. diameter x 18 ft. 9 in. L. Inner diameter: 2.85 in. Thickness: 0.15 in. Inlets/outlets: 3 in. diam. ‘S’ line fitting. Overall dimensions: 20 ft. L x 15 in. W x 30 in. H.
|
|
|
|
HTST Holding Tubes |
| Mfg: |
Model: |
| Stock No. SNPM080.6 |
Serial: |
| HTST Holding Tubes. Heating surface area: 18.22 sq. ft. Holding tubes are equipped with a Balston Steam Filter, Type: 23/75 SR, Element No: 200-75 SR, maximum pressure @ 353 °F: 125, filtering retention: 98% at 0.01 micron, application: culinary steam. Unit uses a Fisher Actuator, Type: 513, size: 20, with a travel of 3/4 in., and an open range of 3-15 sec. Also equipped is a Fisher Electro-pneumatic control, type 646 and TCI Superior Flowmaster flow diversion valve. Inlet: (2) 2 in. dia. S-line fittings. Outlets: (1) 1-1/2 in. dia. S-line fitting. Overall dimensions: 9 ft. 8 in. L x 28 in. W x 66 in. H.
|
|
|
|
Stainless Steel Single Shell Balance/Surge Tank- 65 Gallon |
| Mfg: |
Model: |
| Stock No. HDOC424. |
Serial: |
| Stainless Steel Single Shell Balance/Surge Tank- 65 Gallon. Equipped with measuring glass manometer. Inlets: (1) 2 in. dia. MPT fitting, (1) 4 in. dia. Q-line fitting. Outlets: (1) Tee with 3 in. dia. Q-line fitting and 2 in. dia. butterfly valve. Overall dimensions: 47 in. L x 41 in. W x 39 in. H.
|
|
|
|
Cherry Burrell Balance Tank- 125 Gallon |
| Mfg: Cherry Burrell |
Model:ST |
| Stock No. SSLP543.2a |
Serial: 100 56 284 |
| Cherry Burrell Balance Tank- 125 Gallon. Model: ST, S/N: 100 56 284. Stainless steel. Inside dimensions: 30 in. dia. x 38 in. H. Floatation device activates a butterfly valve that shuts off incoming flow of product. Flip-top lid and ball feet. Inlets: (2) 1-1/2 in. dia. ports, (1) 2 in. dia. S-line fitting (infeed). Outlets: (1) 1-1/2 in. dia. threaded fitting (side), (1) 1-1/2 in. dia. discharge port (tank). Overall dimensions: 55 in. L x 30 in. W x 44-1/2 in. H.
|
|
|
|
Single Shell Balance Tank |
| Mfg: |
Model: |
| Stock No. OI94b |
Serial: |
| Single Shell Balance Tank. Waukesha Pneumatic Valve, S/N 210119 97, Model M61T25U, Catalog No. 02/01/01/01, Valve 61T 2.5 in. U T6. (3) Inlets 2 in., 2-½ in.and 3 in., (1) 4 in. manhole. (2) Outlets 2-½ in. and 2 in. Overall dimensions: 36 in. W, 61-½ in. L, 57 in. H. Has 4 legs at 8 in.
|
|
|
|
Stainless Steel Balance Tank-30 Gallon |
| Mfg: |
Model: |
| Stock No. CCFP516. |
Serial: |
| Stainless Steel Balance Tank-30 Gallon. Model: N/A. S/N: N/A. 316 Stainless Steel construction. Tank Inside Dimensions: 18-1/2 in. Dia. x 24-1/2 in. H. Tank Inlets/Outlets: (1) 3 in. Outlet. Overall Dimensions for Tank: 21 in. L x 22 in. W x 31-1/2 in. H.
|
|
|
|
Balance Tank-120 Gallon Stainless Steel |
| Mfg: |
Model: |
| Stock No. CCFP514. |
Serial: |
| Balance Tank-120 Gallon, Stainless Steel. (4) legs 9 in. H. Top has hopper- 11-1/2 in. dia. Tank has 13 in. x 13 in. square removable splashguard. Inlets/outlets: (3) 2 in. threaded inlets, (1) 2 in. tri-clamp inlet, (1) 3 in. 90° outlet, (1) 5 in. side overflow outlet. Overall dimensions: 49 in. L x 48 in. W x 35-1/2 in. H.
|
|
|
|
Stainless Steel Balance Tank-100 Gallon |
| Mfg: |
Model: |
| Stock No. HDNN828A.5a |
Serial: |
| Stainless Steel Balance Tank- 100 Gallons. Consists of a 2-piece flip-top removable lid and (2) stainless steel floats. Inlets: (1) 2-1/2 in. dia. S-line fitting, (5) 3 in. dia. S-line fittings, (1) 7-1/2 in. dia. port. Outlets: (3) 2 in. dia. S-line fittings, (1) 3 in. dia. S-line fitting, (3) 4 in. dia. S-line fittings, (1) 6 in. dia. S-line fitting. Overall dimensions: 44 in. dia. x 32 in. H.
|
|
|
|
Balance Tank- 120 Gallon |
| Mfg: |
Model: |
| Stock No. EKTF8672.1 |
Serial: |
| Balance Tank- 120 Gallon. Stainless steel. Flip-top lid. Float mechanism, temperature probe, open/close valve controller with solenoid. Inlets: (1) 2 in. dia. S-line fitting. Outlets: (1) 3 in. dia. butterfly valve. Overall dimensions: 55-1/2 in. L x 19 in. W x 60-1/2 in. H.
|
|
|
|
Stainless Steel Balance Tank- 40 Gallon |
| Mfg: Not Specified |
Model: |
| Stock No. TR557B. |
Serial: |
| Stainless Steel Balance Tank- 40 Gallon. 304 stainless steel construction. Inside dimensions: 30 in. dia. x 14 in. H. Tank is equipped with a 7-1/2 in. dia. inspection port. Inlets: (6) 2 in. dia. S-line fittings. Outlets: (1) 2 in. dia. S-line fitting (side), (1) 3 in. dia. S-line butterfly valve (discharge). Overall dimensions: 40 in. L x 34 in. W x 30-1/2 in. H.
|
|
|
|
Stainless Steel Balance Tank- 30 Gallon |
| Mfg: |
Model: |
| Stock No. KPSB172.a |
Serial: |
| Stainless Steel Balance Tank- 30 Gallon. Inside dimensions: 24 in. L x 24 in. W x 14 in. H. Madison Comany Liquid Level Switch, Model: M5600. Inlets: (1) 3 in. dia. S-line fitting, (1) 4 in. dia. S-line fitting. Outlets: (2) 2 in. dia. S-line fittings. Overall dimensions: 29 in. L x 27-1/2 in. W x 27-1/2 in. H.
|
|
|
|
Balance Stainless Steel Tank-40 Gallons |
| Mfg: |
Model: |
| Stock No. OI32b |
Serial: |
| Balance Stainless Steel Tank, 40 gallons, Inside dimensions 24 in. diameter x 20 in. H, domed bottom. (3) legs at 18 in. H. Overall dimensions, 32 in. L x 32 in. W x 34-1/2 in. H. (1) 1 in. outlet.
|
|
|
|
Balance Tank 75 gallon |
| Mfg: |
Model: |
| Stock No. IME2403 |
Serial: |
| 75 Gallon Balance Tank, cover, 2 in. inlet 2-1/2 in. outlet, inner dimensions 40 in. Diameter x 14 in. H, overall dimensions 49 in. W x 25 in. H
|
|
|
|
Cylindrical Balance Tank Stainless Steel |
| Mfg: |
Model: |
| Stock No. 349a |
Serial: |
| Stainless steel cylindrical balance tank, 30 gallon on stand.
|
|
|
|
Stainless Steel Balance Tank-15 Gallons |
| Mfg: |
Model: |
| Stock No. OI30b |
Serial: |
| Stainless Steel Balance Tank, 15 gallons, Inside dimensions 24 in. diameter x 15 in. H. (3) legs, 6-1/2 in. H. (1) 1 in. inlet, (1) 1/2 in. inlet, (1) 2 in. inlet, (1) 1 in. outlet. 6-1/2 in. manhole, 22 in. H with out lid, 23 in. H with lid.
|
|
|
|
Balance Tank - 28 Gallon |
| Mfg: |
Model: |
| Stock No. GOB8171aa |
Serial: |
| Balance tank 28 gallon, 23 in. diameter x 15 in. deep.
|
|
|
|
Balance Tank - 30 Gallon |
| Mfg: |
Model: |
| Stock No. 8.GOB8161aa |
Serial: |
| Balance tank 30 gallon, 23 in. diameter x 17 in. deep.
|
|
|
|
Balance Tank - 30 Gallon |
| Mfg: |
Model: |
| Stock No. 8.GOB8141aa |
Serial: |
| Balance tank 30 gallon, 27 in. diameter x 14 in. deep. Overall height 28 in., without outlets on top 26 in. H. Has 2 manholes, 1 in., 2 in. on lid. Has a 2 in. inlet and 2 in. outlet.
|
|
|
|
Balance Tank - 35 Gallon |
| Mfg: |
Model: |
| Stock No. GOB8211aa |
Serial: |
| Balance tank 35 gallon, 28 in. diameter x 13 in. deep.
|
|
|
|
Balance Tank - 35 Gallon |
| Mfg: |
Model: |
| Stock No. GOB8151aa |
Serial: |
| Balance tank 35 gallon, 28 in. diameter x 14 in. deep.
|
|
|
|
Crepaco PMO Legal Balance Tank - 40 Gallon |
| Mfg: Crepaco |
Model: |
| Stock No. TR-557-Ba |
Serial: |
| Crepaco PMO legal balance tank, 40 gallon. 3/ea 2 in. PV top mounted inlets. 1/ea 2 in. PV side mounted inlet. 2 in. PV outlet. Tank mate level shell only. S/N unknown.
|
|
|
|
Balance Tank Stainless Steel - 40 Gallon |
| Mfg: |
Model: |
| Stock No. 28a |
Serial: |
| Balance tank stainless steel, 40 gallon with one top cover, no model or stock no.
|
|
|
|
Balance Tank Stainless Steel - 250 Gallon |
| Mfg: |
Model: |
| Stock No. LOL6a.1 |
Serial: |
| Balance tank stainless steel 250 gallon.
|
|
|
|
SOLD Balance Tank Single Shell Stainless Steel-30 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. 4.GO892811aa.a |
Serial: |
| Stainless steel single shell balance tank with removable lid, sloped bottom 24 in. diameter, 2 in. threaded inlet, 2-1/2 in. clamp inlets, 1 in. outlet, 6 in.. Overall height 26 in. Without Inlets on top is 21 in.H. Inside dimensions: 17 in. H x 24 in. diameter. 4 in. x 4 in. manhole.
|
|
|
|
SOLD Balance Tank - 20 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. GOB8051aa |
Serial: |
| Balance tank 20 gallon, 24 in. diameter x 10 in. deep.
Overall Height 24 in., with out inlets on top 22 in. H. Has a different top on than the one shown.
SOLD
|
|
|
|
SOLD Balance Tank - 30 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. 8.GOB8131aaa |
Serial: |
| Stainless Steel tank, Inside dimensions 26 in. diameter x 16 in. H. (3) legs, 8 in. H. Overall dimensions 23 in. H. (2) 2 in. inlets, (1) 3 in. inlet, (1) 2 in. outlet with elbow.
SOLD
|
|
|
|
SOLD Balance Tank - 40 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. GOB8191aa |
Serial: |
| Balance tank 40 gallon, 31 in. diameter x 13 in. deep. Overall Height 23 in., height without inlets 21 in. (2) 3 in. outlet, (1) 3-1/2 in. inlet, on lid 8 in. manhole, 2 in. inlet, 3 in. inlet.
SOLD
|
|
|
|
SOLD Stainless Steel Balance Tank-60 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. OI31b |
Serial: |
| Stainless Steel Balance Tank, 60 gallon, with sloped bottom. Inside dimensions 32 in. diameter x 20-1/2 in. H, 14 in. H (short side). 28 in. H with inlets and 26 in. H with out. 8 in. manhole, (6) 2 in. inlets and (1) 3 in. outlet.
SOLD
|
|
|
|
SOLD Balance Tank-200 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. RLOL482.2 |
Serial: |
| Balance Tank-200 Gallon. Stainless Steel, (3) inlets: side inlet- ¾ in., top inlet- 1 ½ in., bottom inlet- ½ in. (1) 4 in. outlet. Unit has 46 in. diameter and is 30 in. deep with domed/ inclined bottom for effective drainage. Overall dimensions are 57 in. diameter x 58 in. high.
SOLD
|
|
|
|
SOLD Cherry Burrell Balance Tank - 250 Gallon SOLD |
| Mfg: Cherry Burrell |
Model: |
| Stock No. RW117a.35 |
Serial: |
| Cherry Burrell balance tank stainless steel 250 gallon, dome top with high pressure jacket, top mounted Lightnin mixer, Model NLDG-300, S/N 81/103938/01, 48 in. diameter x 36 in. high, 18 in. diameter top manway, Lumenite liquid level control, 3 in. air actuated discharge valve, RTD thermocouple.
SOLD
|
|
|
|
SOLD Balance Tank - 55 Gallon SOLD |
| Mfg: |
Model: |
| Stock No. 12a.GOB8 |
Serial: |
| Balance Tank, 50 Gallon, Inner 30 1/2 in Dia. x 17 in Depth, 4 in and 2 in outlets, 2 in side inlet, top 7 1/2 in manway, 3 in top fittings.
SOLD
|
|
|
|
SOLD Waukesha Cherry Burrell Chiller System SOLD |
| Mfg: Waukesha Cherry |
Model: |
| Stock No. TGP354a.20 |
Serial: 97047 |
| Chiller System, Waukesha Cherry Burrell, S/N 97047, Year 1997, 1st Set 24 passes, 7-2-½ in. inlet -outlets and 2-3-½ in., 2nd Set 8 passes, 8-2-½ in. inlet-outlet and 2-3-½ in., 10 ft. H x 21 ft. L x 62 in. W.
SOLD
|
|
|
|
SOLD Junior Pasturizer System SOLD |
| Mfg: |
Model: |
| Stock No. RLOL536.34 |
Serial: |
| Junior Pasturizer System. Stainless steel with APV plate heat exchanger, 24 in. diameter x 18 in. deep balance tank, (2) Tri-Clover pumps on stainless steel frame.
SOLD
|
|
|
|
SOLD Vertical Hot Water Set SOLD |
| Mfg: |
Model:D1012 |
| Stock No. JMB527 |
Serial: 865875 |
| Vertical Hot Water Set, Worthington D-Line Pump, Model D1012, Size 3 in. x 1.5 in. x 10 in., S/N 865875, material 312-8, Max Pressure 275 psi at 100 degrees F, Impeller Dia. 9.3 in., 5 hp 460 volts 1,755 rpm, 2 in. Steam Valve, Marketing Model RBJJ, 81 in. L x 35 in. W x 85 in. H.
SOLD
|
|
|
|
SOLD 1998 Waukesha Cherry Burrell Pasteurizing Skid |
| Mfg: Waukesha |
Model: |
| Stock No. BIIR207. |
Serial: |
| SOLD 1998 Waukesha Cherry Burrell Pasteurizing Skid Package originally purchased by Coke. 60 gpm flow rate with temperature progression 60-150-210-120-64-50, with 0, 15, and 28 second holding tubes option. Today's replacement cost on tube set around $120,000.
|
|
|
|
SOLD Waukesha Cherry Burrell Pasteurizing Skid |
| Mfg: Waukesha |
Model: |
| Stock No. BIIR208. |
Serial: CO170362 |
| SOLD Waukesha Cherry Burrell Pasteurizing Skid. S/N CO170362 (CO16444) Section A: (large pipes) 22, Inlets (1) 3-¾ in. (product), (4) 3 3/4 in. (media). Outlets: (1) 3-¾ in. (product), (4) 3-¾ in. (media). Pipe dimensions: 5 in. diameter, 238 in. L. Section B: (Small pipes) 2, Inlets (1) 2-½ in. (product), (1) 2-¾ in. (media). Outlets: (1) 2-½ in. (product), (1) 2-¾ in. (media). Pipe dimensions: 4 in. diameter, 228 in. L. Product MAWP 515 psi at 250 °F. Media MAWP: 125 psi at 250 °F.
|
|
|
|
SOLD HTST System- 25 GPM SOLD |
| Mfg: |
Model: |
| Stock No. 450.TGP376aa.18 |
Serial: |
| HTST System- 25 GPM. Includes 100 gallon (378 liter) Balance Tank with lumenite level controls, Waukesha Model 60 positive displacement pump with 5hp SEW varidrive, Automatic Flow Divert Valve with Leak Detector, hot water set, 15 second holding tubes, 3 pen ABB Chart Recorder, ABB Flow Meter, and Cherry Burrell Stainless Triple Tube Heat Exchanger with three sections: REGEN, HEATING, and COOLING.
SOLD
|
|
|
|
SOLD Pasteurizer System SOLD |
| Mfg: |
Model: |
| Stock No. 290.TGP376c.18 |
Serial: 91578 |
| Pasteurizer System, Year 1991, Serial 91578, Refrigeration Valves National Board Numbers 42XX, 25 pairs of 3 in Shell Side, MAWP 220 PSI at 300F to -20F, 2 1/2 in Tube Side 500 PSI at 300F to -20F.
SOLD
|
|
|
|
SOLD Vertical Hot Water Set SOLD |
| Mfg: |
Model: |
| Stock No. JMB537 |
Serial: |
| Vertical Hot Water Set. Worthington D-Line pump. Model D1012. S/N 8917-36B. Size 3 in. x 1.5 in. x 10 in. Material 312-8. MAWP: 275 psi @ 100 °F. Impeller dia: 9.3 in. Motor: 5 hp 230/460 V, 1,755 rpm, 2 in. Steam valve. Overall dimensions: 84 in. L x 28 in. W x 87 in. H.
SOLD
|
|
|
|
SOLD APV Anhydro Triple Tube Pasteurizer SOLD |
| Mfg: APV Crepaco |
Model:CTT-C-50.B-38-25-3M |
| Stock No. BIIR601. |
Serial: |
| APV Anhydro Triple Tube Pasteurizer. Model: CTT-C-50.B-38-25-3M. Last used to pasteurize .25 to 4 gpm of 15 degree juice from 30 °F/50 °F to 200 °F; then to cool the same quantity of product from 200 °F to 50 °F/40 °F. Also used to pasteurize .25 to 4 gpm of 50 degree brix juice concentrate from 30 °F/50 °F to 200 °F; then to cool the same quantity of product from 200 °F to 50 °F/40 °F. 316 stainless steel (product side); 304 stainless steel (service side). Overall dimensions: 12 ft. L x 6 ft. W x 7 ft. H. Used in APV pilot plant as grape juice heater/cooler.
SOLD
|
|
|
|
SOLD 1997 FBR Elpo Aseptic Tubular Pasteurizer SOLD |
| Mfg: FBR Elpo |
Model:MHB/1T |
| Stock No. CMT02. |
Serial: |
| 1997 FBR Elpo Aseptic Tubular Pasteurizer. Model MHB/1T. Includes a hopper 38 in. L x 38 in. W x 37 in. H, for raw product introduction. Product level is monitored by (2) SGM Probes. Pasteurizing system consists of (6) Tube in tube heat exchangers. Overall Dimensions: 193 in. L x 86-1/2 in. W x 98 in. H. Unit is in like new condition. Unit also features automatic flow divert valves and CIP operation. Controls include a chart recorder and CIP operation.
SOLD
|
|
|
|
SOLD 2001 APV HTST System- 1,000 gph SOLD |
| Mfg: APV |
Model: |
| Stock No. HDSC124.67 | | |
